3D printed case · Free STL files

Build your case.

A 42 HP Eurorack skiff you print yourself. Pick a layout and your covers, see it in 3D, download exactly the files you need and follow the steps to put it together.

The case is open source. Get the CAD files on GitHub

1 Layout

One 42 HP skiff. Two side panels, two rails, a bottom plate and two slide-in covers.

2 Front cover
3 Back cover
4 Extras

Not available for the Single case. The comb is made for a case tilted at 60 degrees, where the back cover faces up, and this layout lies flat. Pick Two tier, Double two tier or Studio to add it.

5 Preview

Filament colour is for the preview only. The files are the same.

Your case

1 case · 7 parts to print · 6 different files

PrintPartSTL file
1×Side panel, left side-panel-left.stl 173 KB
1×Side panel, right side-panel-right.stl 160 KB
2×Rail Front and back rail are the same partrail.stl 564 KB
1×Bottom plate bottom-plate.stl 406 KB
1×Cover, honeycomb cover-honeycomb.stl 141 KB
1×Cover, solid cover-solid.stl 1 KB

Hardware you also need

  • 8× M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats 4 in the rail ends, 4 in the bottom sockets. Add two more for every module you mount.
  • 8× M3 x 8 mm socket head screw 4 for the rail ends, 4 for the bottom plates. Add two more for every module you mount.
  • Superglue Holds the spacers in their sockets.
Single · 7 parts

Assembly guide

How to build the Single case

7 steps, from the printed parts to a case with modules in it. Select a step to see its parts and the state of the case in the 3D preview.

  1. Print the 7 parts from the print list. Every STL file is already turned the way it should lie on the print bed, so keep that orientation and do not scale the parts. They all fit a 256 x 256 mm bed.

    • Side panels print with the outer face down.
    • The 3D preview lays the parts out on 256 x 256 mm beds to show what there is to print. Your slicer may arrange them differently.

    You need: 1 x Side panel, left, 1 x Side panel, right, 2 x Rail, 1 x Bottom plate, 1 x Cover, honeycomb, 1 x Cover, solid.

  2. The printed parts are held together by M3 spacers and screws, and they are all standard sizes. Order them while the parts print.

    • 8 x M3 hex spacer (standoff): 10 mm long, female thread at both ends, 5.5 mm across the flats. Brass ones work well. The printed sockets are made for 5.5 mm, so check the width before you buy.
    • 8 x M3 x 8 mm socket head screw: 4 for the rail ends, 4 for the bottom plate. The whole case uses this one screw size.
    • For every module you mount: two more spacers and two more M3 x 8 mm screws. Count your modules and add them to the order.
    • Socket head screws are also sold as hex socket cap screws (ISO 4762 or DIN 912). An M3 one has a head 5.5 mm wide and 3 mm high, which is what the printed recesses are made for.
    • Superglue for the spacers, and a 2.5 mm hex key for all the screws.

    You need: 8 x M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats, 8 x M3 x 8 mm socket head screw, Superglue, 2.5 mm hex key.

  3. The case is held together by M3 x 10 mm female hex spacers (standoffs) that sit in printed hex sockets. Put a small drop of superglue in a socket, push the spacer in until it sits just below the surface, and let it cure. Keep the glue out of the thread.

    • Rail ends: 4 spacers, one in every rail end that meets an outer side panel.
    • Bottom sockets: 4 spacers, two in the bottom edge of every side panel.
    • Rail tops: one spacer for every module screw, two per module. Each rail has 21 sockets, one every 2 HP. Only fill the ones you need.

    You need: 8 x M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats, Superglue.

  4. Slide the rail ends into the notches in the top corners of the side panels, from the front and from the back. The hex sockets face up. Front and back rail are the same part. Fix every rail end with an M3 x 8 mm screw through the side panel wall, into the spacer in the rail end.

    You need: 2 x Rail, 4 x M3 x 8 mm socket head screw, 2.5 mm hex key.

  5. Turn the frame upside down. Slide a cover into the front and the back groove from the open bottom, until its top edge sits in the groove under the rail.

    You need: 1 x Cover, honeycomb, 1 x Cover, solid.

  6. With the frame still upside down, set the bottom plate on. The side panels drop into its sockets and the cover edges into its grooves. Fix it with four M3 x 8 mm screws from underneath, into the spacers in the side panels.

    • The four holes in the middle of the plate are for the bus board that powers the modules.

    You need: 1 x Bottom plate, 4 x M3 x 8 mm socket head screw, 2.5 mm hex key.

  7. Turn the case upright. The first module of a row sits next to the 1 HP lip of the left side panel. Fix every module with two M3 x 8 mm screws into the spacers in the rails. The sockets are on a 2 HP grid.

    You need: 2 x M3 x 8 mm socket head screw per module, 2 x M3 x 10 mm hex spacer per module.

The case

  • 42 HP of 3U Eurorack per case
  • Skiff format: 249 x 132.5 mm footprint, 60 mm side panels
  • Every part fits a 256 x 256 mm print bed
  • Slide-in front and back covers in six patterns
  • Open source under the MIT licence: CAD and print files on GitHub

Layouts and their assembly guides

  • Single (1 case · 42 HP): One 42 HP skiff. Two side panels, two rails, a bottom plate and two slide-in covers.
  • Double (2 cases · 84 HP): Two cases side by side. One shared middle frame replaces the two inner side panels.
  • Two tier (2 cases · 84 HP): One case flat and one behind it at 60 degrees, held by two bolt-on stand plates.
  • Double two tier (4 cases · 168 HP): Two Double cases on the stand plates: one flat on the desk and one behind it at 60 degrees.
  • Quad (4 cases · 168 HP): Four cases, two by two in one plane. The side panels and the middle frame are fused end to end, and the inside is open from the front row to the rear row.
  • Studio (6 cases · 252 HP): A double row flat on the desk with a quad set behind it at 60 degrees, on the stand plates.