3D printed case · Free STL files
Build your case.
A 42 HP Eurorack skiff you print yourself. Pick a layout and your covers, see it in 3D, download exactly the files you need and follow the steps to put it together.
The case is open source. Get the CAD files on GitHub
Loading 3D preview…
Your case
Two tier · 84 HP
2 cases · 16 parts to print · 8 different files
| Part | STL file | |
|---|---|---|
| 2× | Side panel, left | side-panel-left.stl 173 KB |
| 2× | Side panel, right | side-panel-right.stl 160 KB |
| 4× | Rail Front and back rail are the same part | rail.stl 564 KB |
| 2× | Bottom plate | bottom-plate.stl 406 KB |
| 2× | Cover, honeycomb | cover-honeycomb.stl 141 KB |
| 2× | Cover, solid | cover-solid.stl 1 KB |
| 1× | Stand plate, left | joiner-left.stl 572 KB |
| 1× | Stand plate, right | joiner-right.stl 572 KB |
Hardware you also need
- 32× M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats 8 in the rail ends, 8 in the bottom sockets, 16 in the stand plate sockets. Add two more for every module you mount.
- 32× M3 x 8 mm socket head screw 8 for the rail ends, 8 for the bottom plates, 16 for the stand plates. Add two more for every module you mount.
- 4× 12 x 12 mm adhesive rubber foot Two under the stand plates, two under the front corners of the lower row. All the same thickness.
- Superglue Holds the spacers in their sockets.
Assembly guide
How to build the Two tier case
8 steps, from the printed parts to a case with modules in it. Select a step to see its parts and the state of the case in the 3D preview.
Print the 16 parts from the print list. Every STL file is already turned the way it should lie on the print bed, so keep that orientation and do not scale the parts. They all fit a 256 x 256 mm bed.
- Side panels print with the outer face down.
- The stand plates only fit the bed diagonally, as supplied. A starting point for them is PETG, 0.2 mm layers, 6 walls and 40 to 50 % infill.
- The 3D preview lays the parts out on 256 x 256 mm beds to show what there is to print. Your slicer may arrange them differently.
You need: 2 x Side panel, left, 2 x Side panel, right, 4 x Rail, 2 x Bottom plate, 2 x Cover, honeycomb, 2 x Cover, solid, 1 x Stand plate, left, 1 x Stand plate, right.
The printed parts are held together by M3 spacers and screws, and they are all standard sizes. Order them while the parts print.
- 32 x M3 hex spacer (standoff): 10 mm long, female thread at both ends, 5.5 mm across the flats. Brass ones work well. The printed sockets are made for 5.5 mm, so check the width before you buy.
- 32 x M3 x 8 mm socket head screw: 8 for the rail ends, 8 for the bottom plates, 16 for the stand plates. The whole case uses this one screw size.
- For every module you mount: two more spacers and two more M3 x 8 mm screws. Count your modules and add them to the order.
- Socket head screws are also sold as hex socket cap screws (ISO 4762 or DIN 912). An M3 one has a head 5.5 mm wide and 3 mm high, which is what the printed recesses are made for.
- 4 x adhesive rubber foot, 12 x 12 mm, all the same thickness.
- Superglue for the spacers, and a 2.5 mm hex key for all the screws.
You need: 32 x M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats, 32 x M3 x 8 mm socket head screw, 4 x 12 x 12 mm adhesive rubber foot, Superglue, 2.5 mm hex key.
The case is held together by M3 x 10 mm female hex spacers (standoffs) that sit in printed hex sockets. Put a small drop of superglue in a socket, push the spacer in until it sits just below the surface, and let it cure. Keep the glue out of the thread.
- Rail ends: 8 spacers, one in every rail end that meets an outer side panel.
- Bottom sockets: 8 spacers, two in the bottom edge of every side panel.
- Rail tops: one spacer for every module screw, two per module. Each rail has 21 sockets, one every 2 HP. Only fill the ones you need.
- Stand plate sockets: 16 spacers, four in each outer side panel. Push them in from inside the case until they sit against the outer wall. A little glue keeps a loose one in place. Do this now: you cannot reach them once the modules are in.
You need: 32 x M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats, Superglue.
Slide the rail ends into the notches in the top corners of the side panels, from the front and from the back. The hex sockets face up. Front and back rail are the same part. Fix every rail end with an M3 x 8 mm screw through the side panel wall, into the spacer in the rail end. Build both cases this way.
You need: 4 x Rail, 8 x M3 x 8 mm socket head screw, 2.5 mm hex key.
Turn the frame upside down. Slide a cover into the front and the back groove of every case from the open bottom, until its top edge sits in the groove under the rail.
You need: 2 x Cover, honeycomb, 2 x Cover, solid.
With the frame still upside down, set a bottom plate on every case. The side panels drop into its sockets and the cover edges into its grooves. Fix each plate with four M3 x 8 mm screws from underneath, into the spacers in the side panels.
- The four holes in the middle of the plate are for the bus board that powers the modules.
You need: 2 x Bottom plate, 8 x M3 x 8 mm socket head screw, 2.5 mm hex key.
Put the lower case flat on the desk. Hold the second case behind it at 60 degrees and support it: a single plate must not carry it alone. Then place one stand plate on each outer side.
- The recesses of a plate face the cases, the screw counterbores face out.
- Start all 16 M3 x 8 mm screws loosely, then tighten them evenly by hand. Stop if a plate rocks, a spacer spins or the plastic starts to crush.
- Stick on four rubber feet of the same thickness: one under the rear foot of each plate, one under each front corner of the lower case.
- The stand is made for a desk. Do not carry the joined cases by the plates.
You need: 1 x Stand plate, left, 1 x Stand plate, right, 16 x M3 x 8 mm socket head screw, 4 x 12 x 12 mm adhesive rubber foot, 2.5 mm hex key.
Turn the case upright. The first module of a row sits next to the 1 HP lip of the left side panel. Fix every module with two M3 x 8 mm screws into the spacers in the rails. The sockets are on a 2 HP grid. Add modules and cables a few at a time, and check that the stand does not rock or slide.
You need: 2 x M3 x 8 mm socket head screw per module, 2 x M3 x 10 mm hex spacer per module.
The case
- 42 HP of 3U Eurorack per case
- Skiff format: 249 x 132.5 mm footprint, 60 mm side panels
- Every part fits a 256 x 256 mm print bed
- Slide-in front and back covers in six patterns
- Open source under the MIT licence: CAD and print files on GitHub
Layouts and their assembly guides
- Single (1 case · 42 HP): One 42 HP skiff. Two side panels, two rails, a bottom plate and two slide-in covers.
- Double (2 cases · 84 HP): Two cases side by side. One shared middle frame replaces the two inner side panels.
- Two tier (2 cases · 84 HP): One case flat and one behind it at 60 degrees, held by two bolt-on stand plates.
- Double two tier (4 cases · 168 HP): Two Double cases on the stand plates: one flat on the desk and one behind it at 60 degrees.
- Quad (4 cases · 168 HP): Four cases, two by two in one plane. The side panels and the middle frame are fused end to end, and the inside is open from the front row to the rear row.
- Studio (6 cases · 252 HP): A double row flat on the desk with a quad set behind it at 60 degrees, on the stand plates.