3D printed case · Free STL files

Build your case.

A 42 HP Eurorack skiff you print yourself. Pick a layout and your covers, see it in 3D, download exactly the files you need and follow the steps to put it together.

The case is open source. Get the CAD files on GitHub

1 Layout

A double row flat on the desk with a quad set behind it at 60 degrees, on the stand plates. A top brace over the middle frame ties the cases together.

2 Front cover
3 Back cover
4 Extras
5 Preview

Filament colour is for the preview only. The files are the same.

Your case

6 cases · 37 parts to print · 13 different files

PrintPartSTL file
1×Side panel, left Lower rowside-panel-left.stl 173 KB
1×Side panel, right Lower rowside-panel-right.stl 160 KB
1×Middle frame Lower rowmiddle-frame.stl 107 KB
1×Fused side panel, left Upper setfused-side-left.stl 346 KB
1×Fused side panel, right Upper setfused-side-right.stl 319 KB
1×Fused middle frame Upper setfused-middle.stl 188 KB
12×Rail Front and back rail are the same partrail.stl 564 KB
6×Bottom plate bottom-plate.stl 406 KB
4×Cover, honeycomb cover-honeycomb.stl 141 KB
4×Cover, solid cover-solid.stl 1 KB
1×Stand plate, left joiner-left.stl 572 KB
1×Stand plate, right joiner-right.stl 572 KB
3×Top brace Required. Goes on top of the modules, across the middle frametop-brace-6hp.stl 2.7 MB

Hardware you also need

  • 52× M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats 12 in the rail ends, 24 in the bottom sockets, 16 in the stand plate sockets. Add two more for every module you mount.
  • 88× M3 x 8 mm socket head screw 12 for the rail ends, 24 for the bottom plates, 16 for the stand plates, up to 36 for the top braces. Add two more for every module you mount.
  • 4× 12 x 12 mm adhesive rubber foot Two under the stand plates, two under the front corners of the lower row. All the same thickness.
  • Superglue Holds the spacers in their sockets.
Studio · 37 parts

Assembly guide

How to build the Studio case

9 steps, from the printed parts to a case with modules in it. Select a step to see its parts and the state of the case in the 3D preview.

  1. Print the 37 parts from the print list. Every STL file is already turned the way it should lie on the print bed, so keep that orientation and do not scale the parts. They all fit a 256 x 256 mm bed.

    • Side panels print with the outer face down.
    • The middle frame needs supports under its two down-facing rail sockets and under the channel on its underside. Keep supports out of the up-facing sockets and the hex pockets.
    • The fused panels only fit the bed diagonally, as supplied. Do not let the slicer turn them. The fused middle frame needs normal supports, not tree supports.
    • The stand plates only fit the bed diagonally, as supplied. A starting point for them is PETG, 0.2 mm layers, 6 walls and 40 to 50 % infill.
    • The top brace prints with its flat side down, without supports.
    • The 3D preview lays the parts out on 256 x 256 mm beds to show what there is to print. Your slicer may arrange them differently.

    You need: 1 x Side panel, left, 1 x Side panel, right, 1 x Middle frame, 1 x Fused side panel, left, 1 x Fused side panel, right, 1 x Fused middle frame, 12 x Rail, 6 x Bottom plate, 4 x Cover, honeycomb, 4 x Cover, solid, 1 x Stand plate, left, 1 x Stand plate, right, 3 x Top brace.

  2. The printed parts are held together by M3 spacers and screws, and they are all standard sizes. Order them while the parts print.

    • 52 x M3 hex spacer (standoff): 10 mm long, female thread at both ends, 5.5 mm across the flats. Brass ones work well. The printed sockets are made for 5.5 mm, so check the width before you buy.
    • 88 x M3 x 8 mm socket head screw: 12 for the rail ends, 24 for the bottom plates, 16 for the stand plates, up to 36 for the top braces. The whole case uses this one screw size.
    • For every module you mount: two more spacers and two more M3 x 8 mm screws. Count your modules and add them to the order.
    • Socket head screws are also sold as hex socket cap screws (ISO 4762 or DIN 912). An M3 one has a head 5.5 mm wide and 3 mm high, which is what the printed recesses are made for.
    • 4 x adhesive rubber foot, 12 x 12 mm, all the same thickness.
    • Superglue for the spacers, and a 2.5 mm hex key for all the screws.

    You need: 52 x M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats, 88 x M3 x 8 mm socket head screw, 4 x 12 x 12 mm adhesive rubber foot, Superglue, 2.5 mm hex key.

  3. The case is held together by M3 x 10 mm female hex spacers (standoffs) that sit in printed hex sockets. Put a small drop of superglue in a socket, push the spacer in until it sits just below the surface, and let it cure. Keep the glue out of the thread.

    • Rail ends: 12 spacers, one in every rail end that meets an outer side panel. The rail ends that go into a middle frame need none.
    • Bottom sockets: 24 spacers, two under each side panel and four under the middle frame of the lower row, four under each fused side panel and eight under the fused middle frame.
    • Rail tops: one spacer for every module screw, two per module. Each rail has 21 sockets, one every 2 HP. Only fill the ones you need.
    • Stand plate sockets: 16 spacers, four in each outer side panel of the lower row and four in the front half of each fused side panel. Push them in from inside the case until they sit against the outer wall. A little glue keeps a loose one in place. Do this now: you cannot reach them once the modules are in.

    You need: 52 x M3 x 10 mm female hex spacer (standoff), 5.5 mm across flats, Superglue.

  4. Build the lower row and the upper set as two separate frames, each from left to right.

    • Lower row: Fit two rails to the left side panel with two M3 x 8 mm screws.
    • Lower row: Slide the middle frame onto the two free rail ends. They go into its closed sockets along their length and need no screws. The lip on the middle frame faces the right case.
    • Lower row: Put the other two rails into the right side of the middle frame, then close the row with the right side panel and two more screws.
    • Lower row: Do not force the rails to the back of the sockets. A small gap is meant to stay there.
    • Upper set: Put four rails, two per row, into the fused left side panel along their length. Fix them with four M3 x 8 mm screws from outside.
    • Upper set: Slide the fused middle frame onto the four free rail ends. No screws there.
    • Upper set: Put the other four rails into the middle frame, then add the fused right side panel and its four screws.

    You need: 12 x Rail, 12 x M3 x 8 mm socket head screw, 2.5 mm hex key.

  5. Turn the frame upside down. Slide a cover into the front and the back groove of every case from the open bottom, until its top edge sits in the groove under the rail.

    • The upper set has no covers between its two rows: the front row only gets a front cover and the rear row only a back cover. The grooves between the rows stay empty.

    You need: 4 x Cover, honeycomb, 4 x Cover, solid.

  6. With the frame still upside down, set a bottom plate on every case. The side panels drop into its sockets and the cover edges into its grooves. Fix each plate with four M3 x 8 mm screws from underneath, into the spacers in the side panels.

    • Two screws of each plate go into the middle frame. Seat a plate on both sides before you tighten it.
    • The four holes in the middle of the plate are for the bus board that powers the modules.

    You need: 6 x Bottom plate, 24 x M3 x 8 mm socket head screw, 2.5 mm hex key.

  7. Put the lower row flat on the desk. Hold the upper set behind it at 60 degrees and support it: a single plate must not carry it alone. Then place one stand plate on each outer side.

    • The recesses of a plate face the cases, the screw counterbores face out.
    • The upper rings of the plates take the front row of the upper set. Its rear row stands above it.
    • Start all 16 M3 x 8 mm screws loosely, then tighten them evenly by hand. Stop if a plate rocks, a spacer spins or the plastic starts to crush.
    • Stick on four rubber feet of the same thickness: one under the rear foot of each plate, one under each front corner of the lower row.
    • The stand is made for a desk. Do not carry the joined cases by the plates.
    • Three rows tip back more easily than two. Keep the stand on a stable desk and do not lean on the top row.

    You need: 1 x Stand plate, left, 1 x Stand plate, right, 16 x M3 x 8 mm socket head screw, 4 x 12 x 12 mm adhesive rubber foot, 2.5 mm hex key.

  8. Turn the case upright. The first module of a row sits next to the 1 HP lip of the left side panel. Fix every module with two M3 x 8 mm screws into the spacers in the rails. The sockets are on a 2 HP grid. Add modules and cables a few at a time, and check that the stand does not rock or slide.

    You need: 2 x M3 x 8 mm socket head screw per module, 2 x M3 x 10 mm hex spacer per module.

  9. Two cases side by side need a top brace: it ties them together across the middle frame. It goes on once all the modules are in. Take out the module screws under its four tabs, lower the brace straight down over the middle frame and fix it with M3 x 8 mm screws through the rail holes of the module panels.

    • Use at least four screws per brace, and up to twelve where the panels under it have holes. Do not drill a panel.
    • Every tab has to lie on a module panel. Fit a blank panel first where a slot is empty.
    • The brace has to lie flat. If it rocks, do not pull it down with the screws.

    You need: 3 x Top brace, Up to 36 x M3 x 8 mm socket head screw.

The case

  • 42 HP of 3U Eurorack per case
  • Skiff format: 249 x 132.5 mm footprint, 60 mm side panels
  • Every part fits a 256 x 256 mm print bed
  • Slide-in front and back covers in six patterns
  • Open source under the MIT licence: CAD and print files on GitHub

Layouts and their assembly guides

  • Single (1 case · 42 HP): One 42 HP skiff. Two side panels, two rails, a bottom plate and two slide-in covers.
  • Double (2 cases · 84 HP): Two cases side by side. One shared middle frame replaces the two inner side panels.
  • Two tier (2 cases · 84 HP): One case flat and one behind it at 60 degrees, held by two bolt-on stand plates.
  • Double two tier (4 cases · 168 HP): Two Double cases on the stand plates: one flat on the desk and one behind it at 60 degrees.
  • Quad (4 cases · 168 HP): Four cases, two by two in one plane. The side panels and the middle frame are fused end to end, and the inside is open from the front row to the rear row.
  • Studio (6 cases · 252 HP): A double row flat on the desk with a quad set behind it at 60 degrees, on the stand plates.